Tag Archives: Dfab Engineering

Dfab Engineering Trackmaster Dozer Crawler Restoration

Trackmaster bulldozer Transmission rebuild 01 – Dissasembly and cleaning

Leave a comment

Take a good look at the photo below, Let it all soak in… Yes this is the state of the transmission when I took it apart. Makes you want to cry a wee little bit huh? But this worked, albiet loudly, it still ran even in this state.

3 speed bulldozer transmission on Trackmaster crawler loader dozer
Interior of the three speed transmission on a Trackmaster bulldozer

Yes and that’s not the worst part of this whole dissassembly process. In the imortal words of the late great Billy Mays, “but wait there’s more!”

Broken Shift fork on a Dfab engineering Trackmaster crawler dozer loader
Broken shift fork Trackmaster 3 speed bulldozer tranmission

The only thing actually broken or wrong, outside of filthy, nasty yuck and a blown up bearing is that one of the shift forks is broken and gone. I’ll have to make a replacement. Thankfully the transmission is a symetrical design and I can use the existing one to aid in making the replacement. There are no parts for these lil dozers, so I’ll have to cast or machine my own new shift fork.

A bit about what I know about this transmission after taking it apart and studying it. The design is a three speed standard splined shaft transmission using sliding standard spur gears. A very simple and robust design, with nothing broken and no unbearable wear or damage despite it’s condition. Shafts, splines, sprockets, snap rings are all SAE. Only the bearings are metric. The three reductions of the tranmision are 1.5:1, 4.5:1, and 18.5:1. These are counted manually by turning the input shaft and counting after rebuild.

The main output shaft is 13/16″ for the sprocket. The bearing on the main shaft is a standard 6305 with bearing dimensions 25x62x17mm Deep Groove Ball Bearing. All of the other bearings are the same and are 6203 Bearings with dimensions 17x40x12mm. There is one oil seal on the output shaft it is an old out of production part Chicago Rawhide Oil Seal 8774, but a modern replacement exists if you can’t find the original. The modern replacement oil seal I found was a SKF 8796 LDS & Small Bore Seal, R Lip Code, CRW1 Style, Inch, 0.875″ Shaft Diameter, 1.624″ Bore Diameter, 0.25″ Width . I ordered this, and then found an original NOS part on Ebay and ordered that as well. they both have the same dimensions and basic design.

destroyed bearing in 3 speed transmission input shaft
A destroyed bearing on the input shaft of a 3 speed dozer transmission

I’m going to just share the rest of the photos as a Gallery of the dissassembly of the 3 speed transmission in my Trackmaster dozer. Mine is a later model Trackmaster, with the hydraulic motor rather than a direct drive off of the motor. You are welcome to click through and look at them all. Dissassembly was relatively easy, with nothing being super siezed in place or broken other than the shift fork.

In the next post I’ll show some reassembly photos and talk a bit about the trick used to pull a blind bearing, cleaning advice for this kind of filth, and more.

If someone stumbles across this page with any information about these Dfab Engineering Trackmaster Dozers Crawlers, I’d love to know more. I’d be happy to host manuals and or parts catalogs here on my blog if you have them and are willing to share them with me. Please leave me a comment or email me at my website name on Gmail (no dot com there). I don’t check often, but I eventually will get back to you to host the information. Thanks!

Dfab Engineering Trackmaster Dozer Crawler Restoration

Trackmaster Dozer Restoration – Part 04 removing the front end loader

Leave a comment
Pulling the Front End Loader from a Dfab Engineering Trackmaster Crawler (Loader Dozer, not a Bulldozer)

I backed the tiny Trackmaster Dozer into the barn and got it centered as best I could for the winter. Not a huge amount of room around the tractor to work on it, but there’s enough. I needed to pull the front end loader arms to get access to all of the components

The cylinder connections and hoses have seen better days. Throughout the Trackmaster crawler uses standard SAE JIC 37 degrees fittings and O-Ring Boss to pumps and motors.

The hoses and fittings have seen better days. I’ll likely repair a lot of these as part of the restoration, either right away or in the future at some point.

Closing off the hydraulics, both lines are the same size and ends I bent them ad sealed off both sides.
Using the hydraulic hose to keep both systems sealed and clean prior to pulling the arms.

The hoses are pretty bad throughout. I’ll be replacing them all in turn. None of them leaked though, and the hydraulics worked well. I used the hoses to seal off the hydraulic systems on both the loader and the dozer side. I want to make sure to keep these systems clean and free of contamination.

If someone stumbles across this page with any information about these Dfab Engineering Trackmaster Dozers Crawlers, I’d love to know more. I’d be happy to host manuals and or parts catalogs here on my blog if you have them and are willing to share them with me. Please leave me a comment or email me at my website name on Gmail (no dot com there). I don’t check often, but I eventually will get back to you to host the information. Thanks!

Dfab Engineering Trackmaster Dozer Crawler Restoration

Trackmaster Loader crawler Restoration PArt 03 welding repairs

Leave a comment
The master link pin on the Tracks for my Dfab Trackmaster.

I promised a few pics of the damaged track drive sprockets to some friends, so the first pics of this post are just that. Further down I’ll get to some minor welding repairs pre dissassembly.

Stripped and poorly welded repairs by some hack who tried to fix this before me.
Stripped and poorly welded repairs by some hack who tried to fix this before me. Note the oversized bolt they used to try and lock it in place on the stripped shaft. Sadness

As you can see in the above photos, I’m going to have some fun fixing this sprockets. I’m not sure if I’ll weld metal back on nicely, and then remachine, or cut it all off and weld in a new hub, possibly of a larger more standard size. The spines on these sprockets, and the interior torque hub gears are bothe ANSI B92.1 1-1/2″ diameter shaft with 23 splines, 16/32DP and 30 deg angle. This is a standard involute spline that unfortunately does not seem to have survived to this day and age. Both the 1-3/4″ and 1-3/8″ see lots of use still today. I will have to figure out what to do after I see and learn more about the small Dozers drive setup.

The dirt guard had been cut/split by someone.

The roller/tensioner dirt shield had been split or cut at some point. It was definitely snapped in the rear section, the front had signs of cutting. I clamped/levered this back together and welded it up. Both the upper and lower parts are attached solidly to the frame and it wasn’t hard to pull the split section perfectly together. It didn’t really require much work to weld this up quickly with some flux. I added a few small strips to the front section. I primarily wanted to prevent misalignment from happening if and when I choose to take this apart this winter.

Counterweight on the back of Tiny Dozer, my Trackmaster by Dfab Engineering

Above you see the counterweight on the rear of the Trackmaster. some of these had backhoes on them. Mine has a counterweight. Near as I can tell, these are Solid steel/iron bars welded together, not tubes filled. I measured and did the math, this weighs about 650 lbs. I wanted to pull this off for the repairs this winter. To do that I needed to replace the Lifting hook on the top of it.

Test fitting a new lift hook onto the counterweight on the tiny bulldozer

I found some 5/8″ steel round bar in my stock pile of metal, got my bender out, and bent up a U shape out of it. I’m quite sad I didn’t take a picture of this, I have a Harbor Freight Bending tool, I mounted to a hitch so I can put it on the back of my truck. I didn’t have a location to bolt it to the floor in my shop, and wanted an immovable rugged mounting for it. Turns out this 5/8″ round was pretty challenging to bend up using it. It does list 5/8″ as the maximum thickness, and it definitely is after trying this out.

Repaired new lifting hook for the ~650lb counterweight on the back of my Trackmaster loader dozer

It was a short quick fix, but it felt good to have actually made a repair. While I was at it I cleaned up the factory welds, metal finished them flat, dressed the corners/edges a bit and sprayed it with a weld through/cold Galvinizing paint to keep it all from rusting. I want to pull this with the tractor and it’ll sit outside all winter. Don’t want my new repair to rust.

Stay tuned for more exciting Tiny Tank Progress and repairs.

If someone stumbles across this page with any information about these Dfab Engineering Trackmaster Dozers Crawlers, I’d love to know more. I’d be happy to host manuals and or parts catalogs here on my blog if you have them and are willing to share them with me. Please leave me a comment or email me at my website name on Gmail (no dot com there). I don’t check often, but I eventually will get back to you to host the information. Thanks!

Dfab Engineering Trackmaster Dozer Crawler Restoration

Dfab Engineering Trackmaster Crawler Dozer Restoration – Part 01

Leave a comment

This is the first post on this winters exciting restoration project. After restoring the Bridgeport Mill last winter, I realized I enjoy having this sort of project to help get through the long cold winters in the New Hampshire. I’m going to try to keep my posts short, contain photos, and actually keep up posting this time around. I’m bad about sharing the projects, like the bridgeport which has been done for a year now and seen several hundred hours of use as an essentially new Milling machine.

I picked up this little guy, with the help of my most awesome neighbor. He has both a bigger truck and an equipement trailer that allowed us to go get this little guy. He’s in sad shape, but also cost less than my lawn mower. I knew he was in rough shape, but as is often the way, you don’t know what that means until you dive into the project.

This is the tensioner on one side. I don’t know what happened, but suspect someone didn’t know the proper way to get the tracks off and used this openeing they made to compress the spring to allow the master link to be removed to get the tracks off.

Dfab Trackmaster Dozer, stripped drive sprocket shaft splines.

The real challenge for this rebuild is going to be dealing with this one problem. The shafts are to the best of my ability to determine, involute splined 1.5 ” 23T with a 16/32DP 30 deg pitch to B92.1 specs. I’m not certain how I will deal with this until I see how bad things are in the drivetrain.

If someone stumbles across this page with any information about these dozers, I’d love to know more. I’d be happy to host manuals and or parts catalogs if you have them and are willing to share.

Dfab Engineering Trackmaster rear drive sprocket and steering clutches.

Here’s a shot of the rear drive assembly. The Trackmaster I bought uses a hydraulic motor into a 3 speed transmission (that was trashed, more later), from there it transmits power to this rear drive set up via #60 chain with a 13T sprocket on transmission, and a 38T split sprocket on the driveshaft. You’ll learn more about this in later posts.

Dfab Engineering Trackmaster Crawler Loader Dozer #60 drive chain, transmission, and hydraulic motor

The above shows the general state of the machine, filthy, unloved, but largely intact and working. I drove it onto and off the trailer, as well as all about once I got it to the homestead. It’s stuck in gear with transmission issues (wait till you see how bad this was in later posts). Stay tuned for lots more. My little machine weighs in at about 4500lbs according to the badly worn tag on it. I wish the model and other info was still readable. It’s a Trackmaster made by d-Fab Engineering by Fruehauf Corp. Route 202, Montgomeryville, Penna., USA. I can’t find a lot of information about these machines, if you have a better image of this tag please contact me. I would love to have a nice new one made for my machine. I’ll eventually try to use this one to generate new art files to make one. If you share a useful image I’ll make a new machine tag for you as well when I do that.

d-Fab Engineering by Fruehauf Corp Trackmaster Crawler Dozer
Trackmaster made by d-Fab Engineering by Fruehauf Corp. Route 202, Montgomeryville, Penna., USA

If someone stumbles across this page with any information about these Dfab Engineering Trackmaster Dozers Crawlers, I’d love to know more. I’d be happy to host manuals and or parts catalogs if you have them and are willing to share. Please leave me a comment or email me at my website name on Gmail (no dot com there). I don’t check often, but I eventually will get back to you to host the information. Thanks!