welder diode replacement

Diode replacement on Lincoln Weld-Pak 100 Welder Repair

welder diode replacement     While working on another project, a diode shorted out in my Lincoln Electric Welder,  a Weld-Pak 100.   I needed to replace this diode but finding information online was challenging.  To help others, and myself in the future,  I am sharing data and specs for the replacement parts I ordered to fix my Lincoln Welder.   I knew the issue was a diode and not a transformer short because it still  made an arc (very poorly), but became a buzz box with the right sound without throwing the internal breaker.  A short in the transformer would likely trip the breaker quickly and not continue to generate an arc.    Opening up the weld-pak 100 and testing the diodes with my digital multimeter with it’s diode setting quickly identified the problem diode.  To do this you have to first remove the diodes from the aluminum plate that acts as their heat sink (or at least the output wires from the plates).

****This project, like many projects by Zac is not a task for the unskilled or those lacking knowledge. Electricity is dangerous!  It can and will kill you!***

If you don’t know exactly what you are doing to be safe, do NOT attempt any kind of repair like this.   Always unplug, and check (verify with a meter safely) that any and all capacitors are discharged fully before testing or working on any electronic device.  I’m sharing this info, primarily to have the data easily accessible should I need to replace or repair my welder again in the future.

welder diode replacement

The Lincoln Weld-Pak 100 diode replacement is a huge PITA.  There is not one smidge of extra wire inside to allow things to move freely making it challenging to work on.  In addition, the transformers are made from wide aluminum strips, and it’s pretty much impossible to move this aluminum strip in the wide direction.   The trick I found to getting the diodes out (they are attached to the rectangular aluminum plates on the left bottom of the above photo) is to undo all of the bolts before trying to get at them.

welder diode replacement Removing what passes for the heat sink (aluminum plate pictured above) from the welder is problematic as well.  Working on this welder is not easy because there’s not a lot of wiggle room on any of the wires.  From a design standpoint this makes sense, least amount of wire will result in the lowest losses.   To get the heat sink plates out use a thin screw driver to pry the inside plastic  clamp and pull the plate towards the front and then up.  I broke off one of the little tabs that locks the plate in place due to prying a bit too much. Thankfully there are two on each plate.

welder diode replacement Above is a side by side photo showing the original diode on the left and the replacements I ordered on the right.  The original rectifier diodes used in the bridge rectifier assembly to generate the DC current used for welding are International Rectofier parts:  IR M9661 40RU (reverse configuration) and IR M9661 40U.  There are 4 diodes in total, and 2 of each part number making up the bridge rectifier assembly.  One of mine was blown, being shorted out such that it allowed electricity to flow in both directions.  These diodes are rated at 70A and 300V based on what I could find on the net, in welder forums and user groups.  The original replacement parts are available from Lincoln and welding supply companies for about $24-30 each.   While that is an option, most of the welder forums recommended replacing the diodes with higher voltage ratings as often they blow due to repeated voltage spikes during the welding process.   I decided to replace all 4 o the diodes in my Lincoln Weld-Pak 100 Welder.  I started my search for replacement parts at Digikey.com (my favorite supplier of electronic parts) but they do not stock higher power rectifier diodes.  I ended up finding what I needed at Newark.co. There were lots of options to choose from,  my choice might not be the best one. If you follow in my footsteps understand this fact.   I as not 100% certain the diode replacement would entirely fix my welder, as such I went with the cheap option.  I ordered two Solid State 85HFR120 and two of Solid State 85HF120 diodes from Newark.com with a total cost plus shipping of considerably less then one replacement OEM diode.   These diodes had the same form factor as the originals and are rated at 85 amps forward current and more importantly a much higher repetitive reverse voltage max of 1200V.

welder diode replacement

Above is the wiring diagram for the Lincoln Weld-Pak 100 Welder.  Thankfully it was inside the welder.  When I looked online I couldn’t find a wiring diagram for my Lincoln Electric Welder and thus I’m sharing it here.  Sometimes it is nice to find things like the circuit diagram for your Weld-Pak welder before you open it up.

welder diode replacement

In order to get the second aluminum plate heat sink out from the welder I had to completely remove the fan assembly.  The plates are supported as well as electrically isolated by the fan assembly so be sure to go careful and not break anything.  When you put it back you need to be very careful that everything is floating in air and no uninsulated parts are touching any other metal parts.    This welder uses air gap to electrically isolate some of the components.

*** Special note ***  DO NOT CUT THE WIRES TO THE DIODES!   There is no extra wire, you MUST DE-SOLDER the wires, and then put them through the new diodes for soldering!   Yes this is not easy, but trust me, if you cut them you will not get it back together without having to replace more things and take the entire welder apart.

welder diode replacement

Replacing the Diodes on the Weld-Pak 100 is pretty straight forward in theory.  Desolder the wires from the old parts, solder on to the new ones.  You may have to squish the wires  while hot with needle nose pliers to get them through the new diodes, or wiggle them in while the solder is melted (using tools not fingers, melted solder is hot).  With all of the diodes replaced you are ready to carefully reassemble the diodes and heat sink plates.  I’m not sure one way is easier then the other. I put the aluminum plates mostly in place but not fully.  This way I could wiggle things into place and then tightened down the nuts.   BE SURE TO USE HEAT SINK PASTE ON THE DIODES when mounting to the Aluminum plate.  I did not have torque specs on the diode nuts, I just made them tightly snug.  Enough so I was sure they wouldn’t come loose, but not tight enough to break anything.

welder diode replacement Once you have it all back together, be sure to check that you have nothing touching that is not supposed to be touching. I used a little bit of Kapton film to insulate the transformer “wire” strip on the off chance that something came in contact with it in the future.   I loosely layed the cover back on and did some test welding.  The welder worked marvelously. I suspect perhaps my diode was iffy for a while as I was once again getting that nice sizzle sound from mig welding.  I realized on hearing it I had not heard that sound quite right for some time.   The bead of weld my weldpak 100 layed down was perfect.  I’ve since welded quite a bit with the repaired welder and everything seems to be great having replaced the rectifier diodes on my Lincoln Weld-Pak 100 Welder.

If you found this post useful, let me know, leave a comment. It’s nice to hear someone found my post useful.

 

 

84 thoughts on “Diode replacement on Lincoln Weld-Pak 100 Welder Repair”

    1. Glad it helped. I’ve recently put 4-5 days welding in on my repaired welder. It’s working great, though I find I have to turn my wire speed down from where it was happy before.

  1. This article helped me diagnose my welder and I did find a bad diode. Opted to replace all four with the ones from Newark as suggested. Did you use hi temp solder for your install? Tried to unsolder the original part with my cheap 100 watt gun (good Weller was at my other shop) and it did nothing.

    1. I used whatever solder I had on hand probably 60/40 from radio shack . My welder has lots of welding on the new diodes and it is welding better then ever with no problems.

  2. Thanks for this information. I had someone else do the repair but your explanation gave me confidence that what I was being charged for and what was being done was all kosher. Thanks again!

      1. How much are the diodes and where can I by them thanks for the info mine buzzes for 10 sec and trips the breaker in the garage not the internal breaker let me know what u think and thank brother love. That some guys give a shit to help others I’ll let u know how I make out Darren trifunidy Niagara Falls canada

        1. Darren,
          It might be you shorted the main transformer or something else is wrong. It’s aluminum sheet wrapped in kapton film as insulator. I have read they sometimes short out. The diodes I ordered are two Solid State 85HFR120 and two of Solid State 85HF120 diodes from Newark.com. Be careful in replacing them correctly, make sure the reverse ones go where the original reverse diodes went.

      2. Hello.thanks for posting this it helped me much.i bought the same diodes as u did from new ark could you tell me where exactly i need to put each one.do both of the same number one go across from each other and wire into the same wire

  3. I think I have a bad transformer because it will not spark at all and all my wires are tight and ground is tight but no spark and I do not hear the hum that I usually hear when I turn the machine on. Is it the transformer? and if so should I attempt repair or send to a shop?

    1. John, It could be a number of issues. Remember this type of equipment is dangerous! If you do not understand electrical safe practices you should not go poking around in a welder. If you do not understand how to troubleshoot the electronics you should certainly take it to a repair shop to have someone who understands electronics and the dangers associated with poking around inside something like a welder.

      Electricity is dangerous, and the kind of voltages and currents in some welders can kill you if you make a mistake or are dumb.

    2. did you find out what the issue is, mine is doing the same thing
      the switch is fine, I have power to the board then I am dead from the relay

  4. Zac!!!!! You are awesome man! Thanks so much for the info and step by step instructions. My weldpak 100 has been beatin up for years, but it kept welding until a few weeks ago. It would make a nasty arc sound when I pushed the trigger. I saw your post and ordered the parts. I bought 4 diodes that you mentioned but ended up just replacing the one that was bad. It was so hard to get the new diode on the wire that I didn’t replace them all. Maybe you could teach us all how to solder these wires to the diodes? I found instructions on youtube on how to test each diode and was able to find the bad one. I put the heat sink paste on before the diode was reinstalled. It looked like the wires that connected to the aluminum plates had the heat paste on them too. I am not sure though. Thanks so much for the info! You are awesome.

    1. Brad. Glad you found my post helpful and were able to repair your welder. It’s nice to hear someone found it useful. Inspires me to put up more posts, I’m a good year behind on the sharing.

      The weldpak 100 is a great little machine, mine prolly has over a thousand hours of arc time on it. Hope yours serves you well.

  5. Hello I have the same problem low power spark should I buy the same diodes you bought or do they have some a little better from there ? I your welder still working fine ? thank you

    1. My welder still works great. I can only advise you to spec your components appropriately for your machine. Do a bit of online research if you are unsure.

  6. My weld Pac 100 is not coming on. I flipped the on off switch a few times and it kicked on then back off. It’s not the breaker or the on off switch. I’m trying to narrow down the problem. Leaning toward the board. Any help would be greatly appreciated. Thanks. Dustin

    1. Hey Dustin, I’m not sure what to tell you. The breaker is not tripping, it just shuts down? is that correct? IT might be a relay. or possibly a bad or corroded wire.

  7. Thanks Zac for taking the time to put up this guide. I stumbled onto your site trying to diagnose my 100. Same symptoms you listed. I ordered the diodes from Newark. Changed them out and cleaned up inside. As you stated, mine must have been lagging for awhile as well, as i hadn’t heard that good sizzle in a very long time. One problem I did have that I didn’t see anybody had mentioned was my old Weller 8200 at 100/140 watt wouldn’t loose the old solder. I ended up buying a D550 at 200/260 watts which did the job. Never the less your guide was very helpful. Thank you for your time.
    (Praise the Lamb who died for me)

    1. I’m glad my post was able to help you out. That’s why I share this stuff. Hard to find time these days, I have like 30 posts “ready to write up” and no time to do it.

  8. My problem is welder comes on trigger will click no wire will feed. Jumped a wire from the two plug in wires terminalssame thing just clicks. Them put volt meter on grey wire at feeder while clicking trigger no voltage.can u let me know what my problem is and how to check diodes to c if they are good or not. The welder the last few times I used it would not get hot enough to burn a good weld

    1. Sounds like you have have a dead wire feed motor or driver. I would guess that it has nothing to do with your diodes. I would test the motor. I’ll try to remember to take a look at mine tonight to make a better suggestion on troubleshooting for you. Depends on if I get home late and have time to poke into my welder
      .

        1. I have this same issue. I found that in the wiring diagram attached above, diode (i believe) 208 on the pc board is blown. It was cracked across with black soot around it. Unfortunately, i cannot read the numbers now, and i cannot find a replacement. I am certain that if i replaced this part, the unit would work. Makes sense to me that the unit “clicks” when the trigger is engaged, but wire does not feed because this diode feeds the wire speed. Any help would be appreciated. The only numbers i can read are: 105…. then +55…… then 022 with maybe a 2 or 7 at the end of the 022, but i cant read it (where crack and flash occurred).

      1. I have the same problem, turn machine on and squeeze the trigger no wire feed but you can hear the clicks. Unplug the wires from the gun and jump the terminals and you hear the same clicks but no wire feed. Removed the motor and tested it. It works with 12 volts to it. No voltage on the motor feed wires.

  9. Thanks for all the information provided. I was able to diagnose the problem with my weldpak 100. I ordered the parts earlier today can’t wait to see if it goes back to laying good welds. I’ll post a comment after I do the repairs on my machine. Again thanks for sharing your knowledge.

    1. Wat was your diagnoses. And What were the parts you ordered to fix welder. I have same issue. I pull trigger and just clicks at the relay. I hook battery to motor and it works I put Bayreuth to wires from relay and motor runs. Is it my pc board?

      1. Oh and I tried switching the A/B/C/D quickly back and forth. And got motor to run for about 30 seconds and now nothing. I cleaned switch contacts on the switch but no luck. Is it my pc board? I need help. I don’t wanna pay $150 for a new pc board. Thanks

        1. I don’t have the welder anymore, I gave it to a young engineer working with me a few years ago. If its just the wire feed motor you are talking about on the welder then it’s something on either the PCB that steps down the voltage to run the motor. You could fix it, but you’d have to be able to diagnose what’s wrong, and then find replacement components. This is not something I could talk you through nor is it something super basic. Since you tried a battery to the motor (again assuming this is the wire feed motor, and you’ve checked the trigger switch works (or you’ve jumped it) then the PCB with whatever DC voltage regualtor/driver for the wire feed motor is your most likely culprit. You could also check the wire speed pot (the thing under the knob you turn) google how to check a potentiometer or something. I assume you can get it to arc if you push some wire out manually and trigger on?

  10. Hi there, hope you can help me. My welder feeds wire at Voltage position A,C&D. No feed at the “B” position but gas does flow. Seems to weld properly at the other positions. (Weld-Pak 100)

    1. I’m not sure but I would guess this is some sort of issue with the switch, rather then an internal short on the transformer. Especially if you are seeing normal welding penetration in C & D.

  11. What thickness will your weld pak100 weld on a single pass using c25 hard wire with .023 wire.

    1. I never used 0.023 wire, I had some 0.025″ wire I would use on thin sheet metal. I almost always welded with 0.030″ and 0.035″ wire. The thickest I could weld well with this machine was only 1/8″. The claims of welding thicker metal seemed exaggerated. I did do a few multi pass preheated 1/4″ welds that held under load on a tractor implement, but it was really a stretch for this welder.

  12. Very interesting reading on repair of weld pak 100 . I’ve got problems with my unit ,: I can not control the wire feed rate , it runs at a constant speed regardless of dial setting . Im checking into the Pc board now , appears to be an SCR motor drive , which i,m told cost 160.00 to purchase ! I can buy a new welder from Harbor Freight for under 120,00 ! Any thoughts that might help me ?
    Thanks Jim

    1. Hi Jim, I have heard the HF welders are decent. If your speed control is not working I would check the Dial. I be it is a potentiometer and sometimes they stop working. If it’s the electronics you likely need a new board. Check ebay. Sometimes you see parts cheap there.

    2. If you have not fixed your welder yet, change out the two transistors on the motor board. They are attached to the black heatsinks. They cost about 4$ each from Newark or digikey.

  13. Your info was helpfull but my weld pack 100 feeds wire just fine but no spark or arce ing at all, what could the possible problem be?

    1. If you need to ask this, you probably should go to a qualified repair shop to have it fixed. There’s no simple solution to troubleshooting a welder and it can be dangerous if you aren’t sure what you are doing.

      1. Zac, I have a HD3200 which exhibited similar symptoms to what you described.
        low arcing current – not sizzling. I am pretty handy electrically and electronically. ordered the Diodes from Newark like you recommended and installed. still have the same problem. Any ideas. looking at the capacitor and transformer. Also going to take a closer look to make sure diodes are installed in the right order. Maybe I swapped them.

        1. Check out your transformer. It may be internally shorted from overheating. If that’s the case you will likely see lower voltage across the electrods when hot than it should be. The specs may be in the manual or you can find them online for your welder.

          1. Hi I have a linclon compact mig the 13 amp fuse blows when I strike an arc and also when it’s above settings 3 any ideas?

  14. Hi Zac, Replaced Diodes as per your instructions , got them from Newark like you said. HD3200 still does not weld with sufficient sizzle- low current. On my capacitor measured 22 volts while operating. Any suggestions. wire feed ok

  15. Many thanks in advance for the insights.
    I have a Lincoln Electric Power MIG 140C.I bought the unit used for my son who will be finishing welding school soon. The following is my son’s input. The unit was working great and has recently stopped working correctly. The open circuit voltage is a 26v and spec says it should be 33v. The unit was also blowing the breaker and the wire was not getting hot enough to form a puddle.
    Any thoughts as to my units problem?

  16. Great information! I just had a weld pac 100 given to me as it was really weak. I bet that the diodes are bad in it also. I can’t wait to tear into it and check them. I have plenty of electronics experience thanks to the USAF.

  17. Im to replace diodes on my 100,but my old diodes are copletly rusted.
    Do you have a way to check witch ones awe the reverse diodes?
    Thanks

  18. The symptoms here seem so much like the failure my little weld pac 100 is experiencing, I went ahead and ordered the diodes you describe here, now just waiting for shipment. I did notice two are a slightly different model, it there any danger of me putting one in the wrong place? I was planning planning on desoldering and soldering the new ones in just as I see them placed, not so good on reading wireing diagrams 🙂

  19. I have a weld Pac 140 and wire fees stops would the diode cause this I have ran 12volts to drive motor and it works

  20. Nicely done write up on how to replace bad diodes. Mine still functions real good. I am setting up mine with a aluminum spoil gun attachment set up. I haven’t got it done yet but a little more work and I will have it done.

  21. Thanks for the post Zac. I have a mig pac10 Turns out its identical. Before I did anything itested the diodes and sure enough one was open. I ordered the 4 Diodes
    85hfr40 and 85hf40 Installed it and its fine.
    If maybe because the diodes are new, but the welder seems to have a stronger arc.
    Ive been letting it cool inbetween beads and its good so far.
    Again many thanks. Danylo Iwanusiw (ya just call me Dan)

  22. Great job brother I am repairing my brothers weld pack and you just took the long diag time out of the equation.
    Nice to find good things onlone! God bless you!

  23. awesome write up I had the exact problem with mine and local welding supply wanted over $100 for new set of diodes found your write up I ordered parts and my weld oak works excel at again. Thank you.

  24. Great article Zac!
    I jumped the gun and removed the easy diodes BEFORE checking which one goes where.
    Is it safe to assume(?)that the similar diodes connect to same wires from front to the back side diodes?
    I hope that question makes sense.
    Thanks in advance.

  25. I bought a welder in an auction and have been looking for pictures of the inside for some time now. The welder was torn apart (didn’t realize that when i bid on it) and I need to reattach the diodes to the alum. plate. The pictures are a God send. They will help me put everything back in its original location.

    Once it’s back together, I will try to plug in and see what happens. Might be coming back to this for another repair. Thank you for the information!!!

    1. I think there was a small solenoid board I had to install along with the gas fitting and parts. IT was a long time ago and I gave my welder to a student/friend a number of years ago when I upgraded to a bigger welder so I can’t go look. Sorry.

  26. Good morning , pick up HD 100 , didnt have the ground cable installed one kinda long 15ft 6 gauge , dont know the recommended length, could that be the reason for a very low arc, or could the cable/gun could be the problem also looks like it was shortened about a foot

    1. a long cable could add resistance, I’ve never seen a gun/cable shortened. Can’t imagine that works well. The gun itself just triggers things, but if there’s a bad connection on the cable to the tip or something similar you could also have a bad arc. You have to do some troubleshooting, or bring it to a shop to have them test it if you are unsure what that means

  27. Thanks to this post, I was able to fix my Lincoln. I used the same diodes. Only issue had was melting the solder with my tiny solder gun. I decided to use my propane torch and worked like a charm. Just had to be careful I didn’t burn anything. Put back together and worked good as new.

  28. I have the same welder, lincoln weld pac 100, i removed all 4 diodes and going to order them.But i really need your help, I did not mark the diodes,so the ones ending in RU and U – I dont know where they go! in which position anyway. I cannot seem to find a diagram on the internet that will show me. if you could just open your machine and look inside i would really appreciate that,thanks.

  29. this is great! ty!
    im going to try to repair an sp100-t that was given to me. all 4 diodes test open and the plates are missing. ive cut out “new” plates and have your recommended diodes on the way however without disassembling it myself im a bit confused as to where the diodes go? from what i can see from a parts diagram the “R” diodes go on top? (one on each side? ). kind of excited to see if the welder will work! thanks and i share the same “i can fix that or make it better” as you seem to do. fun stuff!

  30. yes they do and yes it works! great welder for about a 50 $ chance. it can use gas however i dont think ill make that investment . bought a roll of .030 flux core and it seems to work great! thanks for sharing this info!

  31. Good morning, diodes check good in my Weld pak 100, voltage is 30 volt Dc no load and 15 to 18 volts loaded. Very low arc!
    What are the chances that the capacitor is weak?
    Only way i have to test is with ohm meter, it give appearance of some charge or capacitance.
    I’m puzzled!

  32. Mitch, My Lincoln Wel-Pac 100 had always work just fine until recently. When I pull the trigger there is an ark and then stop. Only an ark! It appears to be a circuit breaker but from everything I have seen of your comments so far everything is a diode problem?

    Thanks for any help

  33. Nice article. Can a bad diode(s) result in a loss of arc with fan and wire feeder operational? Is a loss of arc more likely a transformer issue or a bad board issue? I have the Lincoln service manual for my 140c and all voltage readings are OK except the transformer reading is 109VAC when it should read 120VAC according to the manual. Any thoughts as to what a low reading here may mean?

    1. It could be, but you need to do some more trouble shooting, or find a friend with electronics experience. Be careful not to electrocute yourself

  34. I have A Lincoln hd 140 and as I was welding at full power flux core doing a long bead my machine made a loud Pop noise like something exploded inside the machine. any clue what it is? its not working anymore…

  35. Thank you for that info. I have Lincoln weld pak 100 reading your info I can fix my. From Texarkana Ar.

  36. This is a very well done and complete repair illustration. I was ready to chuck my WeldPak 100 until I read this article. I ordered the same diodes from Newark and saved a lot of money getting my welder working again for less than $40!

    I would add that while removing the fan and black plastic bracket to be careful as it is very brittle. Trying to remove the aluminum plates without removing the fan as suggested will result in a broken bracket.

  37. Very good, could help me. I searched the internet and could not find the transistors numbers on my weld pack 100. Both burnt badly. Could you help me with the transistors numbers. Thanks

  38. Hi Zac , my name is Randy Freeman and I live in Yorktown Va.
    So a few years ago I was in the middle of a 20′ trailer build when my weld pak 100 decided to quit welding. It would produce an arc but not hot enough to weld with. I decided to take it to Arcet welding supplies as I had been told that they offered welder repair services. They called me and informed me that I had bad bridge rectifiers and a bad capacitor and wanted $400 and some dollars to make the repairs . I only paid a little over $300 for that welder brand new so I definitely wasn’t going to pay that for them to repair.
    Of course when I got home with it I noticed a lot of the wires were disconnected which was a problem being that I wasn’t the one that unhooked them which left me not sure what went where.
    Anyhow after ordering the parts and installing them and hooking everything back up to where I was pretty sure that it probably went I finally decided to give it a try and so I did . I pulled the trigger and nothing happened it wouldn’t feed any wire or do anything.
    I’m an electrician by trade but I had no experience with rectifiers/ diodes or how to replace them so I did my best. I wondered if trying to solder the wires on to the diodes that maybe the heat damaged them and that’s what might be making the welder not work.
    Of course there no telling how Arcet did there testing or if they possibly damaged something in way of testing. IDK I’ve held on to that welder because it was my very first welding machine and to be honest it was probably the best welder I’ve ever owned to this day.

    I’m really greatful to you for posting this and wished I had found it so much sooner. Despite the fact that I have several welding machines I still would love to have my very first one working again. That would bring me more joy than most people could possibly understand. Hopefully you know where I’m coming from , sentimental value is priceless. LOL

    If you have any ideas I’d be glad to hear them especially since electronics are a little out of my expertise so to speak.
    It’s a real shame that Lincoln quit making this particular welder as it was remarkably reliable and produced great welds with real strength!

    Thanks again for your post and all the information that you have made available to the public. I have no doubt that this has helped hundreds of not thousands of people out there.

Leave a Reply

Your email address will not be published. Required fields are marked *